120 Series Speeds & Feeds | Cutting Parameters by Material | Sonic Tools

Cutting parameters by material

120 Series Speeds & Feeds

Each row applies to every 120 Series part number at that diameter.

View 120 Series end mills

VcCutting speed
AeRadial width of cut
ApAxial depth of cut
FzFeed per tooth
Construction Steel

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 360 0.125 0.025 0.0003
0.125 Roughing Side 425 0.025 0.125 0.0005
0.125 Roughing Contour 460 0.0038 0.0038 0.0006
0.125 Finishing Side 510 0.0031 0.1 0.0003
0.125 Finishing Slot 430 0.0031 0.1 0.0002
0.125 Finishing Contour 550 0.0031 0.0031 0.0004
0.1563 Roughing Slot 360 0.1563 0.0313 0.0006
0.1563 Roughing Side 425 0.0313 0.1563 0.0009
0.1563 Roughing Contour 460 0.0047 0.0047 0.0013
0.1563 Finishing Side 510 0.0039 0.125 0.0007
0.1563 Finishing Slot 430 0.0039 0.125 0.0004
0.1563 Finishing Contour 550 0.0039 0.0039 0.0009
0.1875 Roughing Slot 360 0.1875 0.0375 0.0006
0.1875 Roughing Side 425 0.0375 0.1875 0.0009
0.1875 Roughing Contour 460 0.0056 0.0056 0.0013
0.1875 Finishing Side 510 0.0047 0.15 0.0007
0.1875 Finishing Slot 430 0.0047 0.15 0.0004
0.1875 Finishing Contour 550 0.0047 0.0047 0.0009
0.25 Roughing Slot 360 0.25 0.05 0.0006
0.25 Roughing Side 425 0.05 0.25 0.0009
0.25 Roughing Contour 460 0.0075 0.0075 0.0013
0.25 Finishing Side 510 0.0063 0.2 0.0007
0.25 Finishing Slot 430 0.0063 0.2 0.0004
0.25 Finishing Contour 550 0.0063 0.0063 0.0009
0.3125 Roughing Slot 360 0.3125 0.0625 0.0013
0.3125 Roughing Side 425 0.0625 0.3125 0.0019
0.3125 Roughing Contour 460 0.0094 0.0094 0.0025
0.3125 Finishing Side 510 0.0078 0.25 0.0013
0.3125 Finishing Slot 430 0.0078 0.25 0.0009
0.3125 Finishing Contour 550 0.0078 0.0078 0.0018
0.375 Roughing Slot 360 0.375 0.075 0.0013
0.375 Roughing Side 425 0.075 0.375 0.0019
0.375 Roughing Contour 460 0.0113 0.0113 0.0025
0.375 Finishing Side 510 0.0094 0.3 0.0013
0.375 Finishing Slot 430 0.0094 0.3 0.0009
0.375 Finishing Contour 550 0.0094 0.0094 0.0018
0.5 Roughing Slot 360 0.5 0.1 0.0019
0.5 Roughing Side 425 0.1 0.5 0.0028
0.5 Roughing Contour 460 0.015 0.015 0.0038
0.5 Finishing Side 510 0.0125 0.4 0.002
0.5 Finishing Slot 430 0.0125 0.4 0.0013
0.5 Finishing Contour 550 0.0125 0.0125 0.0026
0.625 Roughing Slot 360 0.625 0.125 0.0019
0.625 Roughing Side 425 0.125 0.625 0.0028
0.625 Roughing Contour 460 0.0188 0.0188 0.0038
0.625 Finishing Side 510 0.0156 0.5 0.002
0.625 Finishing Slot 430 0.0156 0.5 0.0013
0.625 Finishing Contour 550 0.0156 0.0156 0.0026
0.75 Roughing Slot 360 0.75 0.15 0.0031
0.75 Roughing Side 425 0.15 0.75 0.0047
0.75 Roughing Contour 460 0.0225 0.0225 0.0063
0.75 Finishing Side 510 0.0188 0.6 0.0033
0.75 Finishing Slot 430 0.0188 0.6 0.0022
0.75 Finishing Contour 550 0.0188 0.0188 0.0044

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 130 0.6 3 0.012
3 Roughing Slot 110 3 0.6 0.008
3 Roughing Contour 140 0.09 0.09 0.016
4 Roughing Side 130 0.8 4 0.024
4 Roughing Slot 110 4 0.8 0.016
4 Roughing Contour 140 0.12 0.12 0.032
5 Roughing Side 130 1 5 0.024
5 Roughing Slot 110 5 1 0.016
5 Roughing Contour 140 0.15 0.15 0.032
6 Roughing Side 130 1.2 6 0.024
6 Roughing Slot 110 6 1.2 0.016
6 Roughing Contour 140 0.18 0.18 0.032
8 Roughing Side 130 1.6 8 0.048
8 Roughing Slot 110 8 1.6 0.032
8 Roughing Contour 140 0.24 0.24 0.064
10 Roughing Side 130 2 10 0.048
10 Roughing Slot 110 10 2 0.032
10 Roughing Contour 140 0.3 0.3 0.064
12 Roughing Side 130 2.4 12 0.072
12 Roughing Slot 110 12 2.4 0.048
12 Roughing Contour 140 0.36 0.36 0.096
16 Roughing Side 130 3.2 16 0.072
16 Roughing Slot 110 16 3.2 0.048
16 Roughing Contour 140 0.48 0.48 0.096
20 Roughing Side 130 4 20 0.12
20 Roughing Slot 110 20 4 0.08
20 Roughing Contour 140 0.6 0.6 0.16
3 Finishing Side 155 0.075 2.4 0.008
3 Finishing Slot 130 0.075 2.4 0.006
3 Finishing Contour 170 0.075 0.075 0.011
4 Finishing Side 155 0.1 3.2 0.017
4 Finishing Slot 130 0.1 3.2 0.011
4 Finishing Contour 170 0.1 0.1 0.022
5 Finishing Side 155 0.125 4 0.017
5 Finishing Slot 130 0.125 4 0.011
5 Finishing Contour 170 0.125 0.125 0.022
6 Finishing Side 155 0.15 4.8 0.017
6 Finishing Slot 130 0.15 4.8 0.011
6 Finishing Contour 170 0.15 0.15 0.022
8 Finishing Side 155 0.2 6.4 0.034
8 Finishing Slot 130 0.2 6.4 0.022
8 Finishing Contour 170 0.2 0.2 0.045
10 Finishing Side 155 0.25 8 0.034
10 Finishing Slot 130 0.25 8 0.022
10 Finishing Contour 170 0.25 0.25 0.045
12 Finishing Side 155 0.3 9.6 0.05
12 Finishing Slot 130 0.3 9.6 0.034
12 Finishing Contour 170 0.3 0.3 0.067
16 Finishing Side 155 0.4 12.8 0.05
16 Finishing Slot 130 0.4 12.8 0.034
16 Finishing Contour 170 0.4 0.4 0.067
20 Finishing Side 155 0.5 16 0.084
20 Finishing Slot 130 0.5 16 0.056
20 Finishing Contour 170 0.5 0.5 0.112
Ductile Cast Iron

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 295 0.125 0.0125 0.0002
0.125 Roughing Side 360 0.0125 0.125 0.0005
0.125 Roughing Contour 395 0.0038 0.0038 0.0006
0.125 Finishing Side 430 0.0031 0.1 0.0004
0.125 Finishing Slot 350 0.0031 0.1 0.0002
0.125 Finishing Contour 475 0.0031 0.0031 0.0004
0.1563 Roughing Slot 295 0.1563 0.0156 0.0005
0.1563 Roughing Side 360 0.0156 0.1563 0.001
0.1563 Roughing Contour 395 0.0047 0.0047 0.0012
0.1563 Finishing Side 430 0.0039 0.125 0.0007
0.1563 Finishing Slot 350 0.0039 0.125 0.0004
0.1563 Finishing Contour 475 0.0039 0.0039 0.0008
0.1875 Roughing Slot 295 0.1875 0.0188 0.0005
0.1875 Roughing Side 360 0.0188 0.1875 0.001
0.1875 Roughing Contour 395 0.0056 0.0056 0.0012
0.1875 Finishing Side 430 0.0047 0.15 0.0007
0.1875 Finishing Slot 350 0.0047 0.15 0.0004
0.1875 Finishing Contour 475 0.0047 0.0047 0.0008
0.25 Roughing Slot 295 0.25 0.025 0.0005
0.25 Roughing Side 360 0.025 0.25 0.001
0.25 Roughing Contour 395 0.0075 0.0075 0.0012
0.25 Finishing Side 430 0.0063 0.2 0.0007
0.25 Finishing Slot 350 0.0063 0.2 0.0004
0.25 Finishing Contour 475 0.0063 0.0063 0.0008
0.3125 Roughing Slot 295 0.3125 0.0313 0.001
0.3125 Roughing Side 360 0.0313 0.3125 0.002
0.3125 Roughing Contour 395 0.0094 0.0094 0.0024
0.3125 Finishing Side 430 0.0078 0.25 0.0014
0.3125 Finishing Slot 350 0.0078 0.25 0.0007
0.3125 Finishing Contour 475 0.0078 0.0078 0.0017
0.375 Roughing Slot 295 0.375 0.0375 0.001
0.375 Roughing Side 360 0.0375 0.375 0.002
0.375 Roughing Contour 395 0.0113 0.0113 0.0024
0.375 Finishing Side 430 0.0094 0.3 0.0014
0.375 Finishing Slot 350 0.0094 0.3 0.0007
0.375 Finishing Contour 475 0.0094 0.0094 0.0017
0.5 Roughing Slot 295 0.5 0.05 0.0015
0.5 Roughing Side 360 0.05 0.5 0.0031
0.5 Roughing Contour 395 0.015 0.015 0.0035
0.5 Finishing Side 430 0.0125 0.4 0.0021
0.5 Finishing Slot 350 0.0125 0.4 0.001
0.5 Finishing Contour 475 0.0125 0.0125 0.0025
0.625 Roughing Slot 295 0.625 0.0625 0.0015
0.625 Roughing Side 360 0.0625 0.625 0.0031
0.625 Roughing Contour 395 0.0188 0.0188 0.0035
0.625 Finishing Side 430 0.0156 0.5 0.0021
0.625 Finishing Slot 350 0.0156 0.5 0.001
0.625 Finishing Contour 475 0.0156 0.0156 0.0025
0.75 Roughing Slot 295 0.75 0.075 0.0025
0.75 Roughing Side 360 0.075 0.75 0.0051
0.75 Roughing Contour 395 0.0225 0.0225 0.0059
0.75 Finishing Side 430 0.0188 0.6 0.0036
0.75 Finishing Slot 350 0.0188 0.6 0.0018
0.75 Finishing Contour 475 0.0188 0.0188 0.0041

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 110 0.3 3 0.013
3 Roughing Slot 90 3 0.3 0.006
3 Roughing Contour 120 0.09 0.09 0.015
4 Roughing Side 110 0.4 4 0.026
4 Roughing Slot 90 4 0.4 0.013
4 Roughing Contour 120 0.12 0.12 0.03
5 Roughing Side 110 0.5 5 0.026
5 Roughing Slot 90 5 0.5 0.013
5 Roughing Contour 120 0.15 0.15 0.03
6 Roughing Side 110 0.6 6 0.026
6 Roughing Slot 90 6 0.6 0.013
6 Roughing Contour 120 0.18 0.18 0.03
8 Roughing Side 110 0.8 8 0.052
8 Roughing Slot 90 8 0.8 0.026
8 Roughing Contour 120 0.24 0.24 0.06
10 Roughing Side 110 1 10 0.052
10 Roughing Slot 90 10 1 0.026
10 Roughing Contour 120 0.3 0.3 0.06
12 Roughing Side 110 1.2 12 0.078
12 Roughing Slot 90 12 1.2 0.038
12 Roughing Contour 120 0.36 0.36 0.09
16 Roughing Side 110 1.6 16 0.078
16 Roughing Slot 90 16 1.6 0.038
16 Roughing Contour 120 0.48 0.48 0.09
20 Roughing Side 110 2 20 0.13
20 Roughing Slot 90 20 2 0.064
20 Roughing Contour 120 0.6 0.6 0.15
3 Finishing Side 130 0.075 2.4 0.009
3 Finishing Slot 110 0.075 2.4 0.004
3 Finishing Contour 145 0.075 0.075 0.011
4 Finishing Side 130 0.1 3.2 0.018
4 Finishing Slot 110 0.1 3.2 0.009
4 Finishing Contour 145 0.1 0.1 0.021
5 Finishing Side 130 0.125 4 0.018
5 Finishing Slot 110 0.125 4 0.009
5 Finishing Contour 145 0.125 0.125 0.021
6 Finishing Side 130 0.15 4.8 0.018
6 Finishing Slot 110 0.15 4.8 0.009
6 Finishing Contour 145 0.15 0.15 0.021
8 Finishing Side 130 0.2 6.4 0.036
8 Finishing Slot 110 0.2 6.4 0.018
8 Finishing Contour 145 0.2 0.2 0.042
10 Finishing Side 130 0.25 8 0.036
10 Finishing Slot 110 0.25 8 0.018
10 Finishing Contour 145 0.25 0.25 0.042
12 Finishing Side 130 0.3 9.6 0.055
12 Finishing Slot 110 0.3 9.6 0.027
12 Finishing Contour 145 0.3 0.3 0.063
16 Finishing Side 130 0.4 12.8 0.055
16 Finishing Slot 110 0.4 12.8 0.027
16 Finishing Contour 145 0.4 0.4 0.063
20 Finishing Side 130 0.5 16 0.091
20 Finishing Slot 110 0.5 16 0.045
20 Finishing Contour 145 0.5 0.5 0.105
Grey Cast Iron

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 325 0.125 0.025 0.0004
0.125 Roughing Side 395 0.025 0.125 0.0007
0.125 Roughing Contour 425 0.0038 0.0038 0.0007
0.125 Finishing Side 470 0.0031 0.1 0.0005
0.125 Finishing Slot 390 0.0031 0.1 0.0002
0.125 Finishing Contour 510 0.0031 0.0031 0.0005
0.1563 Roughing Slot 325 0.1563 0.0313 0.0007
0.1563 Roughing Side 395 0.0313 0.1563 0.0013
0.1563 Roughing Contour 425 0.0047 0.0047 0.0015
0.1563 Finishing Side 470 0.0039 0.125 0.0009
0.1563 Finishing Slot 390 0.0039 0.125 0.0005
0.1563 Finishing Contour 510 0.0039 0.0039 0.001
0.1875 Roughing Slot 325 0.1875 0.0375 0.0007
0.1875 Roughing Side 395 0.0375 0.1875 0.0013
0.1875 Roughing Contour 425 0.0056 0.0056 0.0015
0.1875 Finishing Side 470 0.0047 0.15 0.0009
0.1875 Finishing Slot 390 0.0047 0.15 0.0005
0.1875 Finishing Contour 510 0.0047 0.0047 0.001
0.25 Roughing Slot 325 0.25 0.05 0.0007
0.25 Roughing Side 395 0.05 0.25 0.0013
0.25 Roughing Contour 425 0.0075 0.0075 0.0015
0.25 Finishing Side 470 0.0063 0.2 0.0009
0.25 Finishing Slot 390 0.0063 0.2 0.0005
0.25 Finishing Contour 510 0.0063 0.0063 0.001
0.3125 Roughing Slot 325 0.3125 0.0625 0.0014
0.3125 Roughing Side 395 0.0625 0.3125 0.0027
0.3125 Roughing Contour 425 0.0094 0.0094 0.003
0.3125 Finishing Side 470 0.0078 0.25 0.0019
0.3125 Finishing Slot 390 0.0078 0.25 0.001
0.3125 Finishing Contour 510 0.0078 0.0078 0.0021
0.375 Roughing Slot 325 0.375 0.075 0.0014
0.375 Roughing Side 395 0.075 0.375 0.0027
0.375 Roughing Contour 425 0.0113 0.0113 0.003
0.375 Finishing Side 470 0.0094 0.3 0.0019
0.375 Finishing Slot 390 0.0094 0.3 0.001
0.375 Finishing Contour 510 0.0094 0.0094 0.0021
0.5 Roughing Slot 325 0.5 0.1 0.0021
0.5 Roughing Side 395 0.1 0.5 0.004
0.5 Roughing Contour 425 0.015 0.015 0.0045
0.5 Finishing Side 470 0.0125 0.4 0.0028
0.5 Finishing Slot 390 0.0125 0.4 0.0015
0.5 Finishing Contour 510 0.0125 0.0125 0.0031
0.625 Roughing Slot 325 0.625 0.125 0.0021
0.625 Roughing Side 395 0.125 0.625 0.004
0.625 Roughing Contour 425 0.0188 0.0188 0.0045
0.625 Finishing Side 470 0.0156 0.5 0.0028
0.625 Finishing Slot 390 0.0156 0.5 0.0015
0.625 Finishing Contour 510 0.0156 0.0156 0.0031
0.75 Roughing Slot 325 0.75 0.15 0.0035
0.75 Roughing Side 395 0.15 0.75 0.0067
0.75 Roughing Contour 425 0.0225 0.0225 0.0075
0.75 Finishing Side 470 0.0188 0.6 0.0047
0.75 Finishing Slot 390 0.0188 0.6 0.0025
0.75 Finishing Contour 510 0.0188 0.0188 0.0052

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 120 0.6 3 0.017
3 Roughing Slot 100 3 0.6 0.009
3 Roughing Contour 130 0.09 0.09 0.019
4 Roughing Side 120 0.8 4 0.034
4 Roughing Slot 100 4 0.8 0.018
4 Roughing Contour 130 0.12 0.12 0.038
5 Roughing Side 120 1 5 0.034
5 Roughing Slot 100 5 1 0.018
5 Roughing Contour 130 0.15 0.15 0.038
6 Roughing Side 120 1.2 6 0.034
6 Roughing Slot 100 6 1.2 0.018
6 Roughing Contour 130 0.18 0.18 0.038
8 Roughing Side 120 1.6 8 0.068
8 Roughing Slot 100 8 1.6 0.036
8 Roughing Contour 130 0.24 0.24 0.076
10 Roughing Side 120 2 10 0.068
10 Roughing Slot 100 10 2 0.036
10 Roughing Contour 130 0.3 0.3 0.076
12 Roughing Side 120 2.4 12 0.102
12 Roughing Slot 100 12 2.4 0.054
12 Roughing Contour 130 0.36 0.36 0.114
16 Roughing Side 120 3.2 16 0.102
16 Roughing Slot 100 16 3.2 0.054
16 Roughing Contour 130 0.48 0.48 0.114
20 Roughing Side 120 4 20 0.17
20 Roughing Slot 100 20 4 0.09
20 Roughing Contour 130 0.6 0.6 0.19
3 Finishing Side 145 0.075 2.4 0.012
3 Finishing Slot 120 0.075 2.4 0.006
3 Finishing Contour 155 0.075 0.075 0.013
4 Finishing Side 145 0.1 3.2 0.024
4 Finishing Slot 120 0.1 3.2 0.013
4 Finishing Contour 155 0.1 0.1 0.027
5 Finishing Side 145 0.125 4 0.024
5 Finishing Slot 120 0.125 4 0.013
5 Finishing Contour 155 0.125 0.125 0.027
6 Finishing Side 145 0.15 4.8 0.024
6 Finishing Slot 120 0.15 4.8 0.013
6 Finishing Contour 155 0.15 0.15 0.027
8 Finishing Side 145 0.2 6.4 0.048
8 Finishing Slot 120 0.2 6.4 0.025
8 Finishing Contour 155 0.2 0.2 0.053
10 Finishing Side 145 0.25 8 0.048
10 Finishing Slot 120 0.25 8 0.025
10 Finishing Contour 155 0.25 0.25 0.053
12 Finishing Side 145 0.3 9.6 0.071
12 Finishing Slot 120 0.3 9.6 0.038
12 Finishing Contour 155 0.3 0.3 0.08
16 Finishing Side 145 0.4 12.8 0.071
16 Finishing Slot 120 0.4 12.8 0.038
16 Finishing Contour 155 0.4 0.4 0.08
20 Finishing Side 145 0.5 16 0.119
20 Finishing Slot 120 0.5 16 0.063
20 Finishing Contour 155 0.5 0.5 0.133
Stainless Steel

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 165 0.125 0.0125 0.0002
0.125 Roughing Side 230 0.0125 0.125 0.0005
0.125 Roughing Contour 260 0.0038 0.0038 0.0006
0.125 Finishing Side 275 0.0031 0.1 0.0003
0.125 Finishing Slot 200 0.0031 0.1 0.0002
0.125 Finishing Contour 310 0.0031 0.0031 0.0004
0.1563 Roughing Slot 165 0.1563 0.0156 0.0005
0.1563 Roughing Side 230 0.0156 0.1563 0.0009
0.1563 Roughing Contour 260 0.0047 0.0047 0.0012
0.1563 Finishing Side 275 0.0039 0.125 0.0007
0.1563 Finishing Slot 200 0.0039 0.125 0.0004
0.1563 Finishing Contour 310 0.0039 0.0039 0.0008
0.1875 Roughing Slot 165 0.1875 0.0188 0.0005
0.1875 Roughing Side 230 0.0188 0.1875 0.0009
0.1875 Roughing Contour 260 0.0056 0.0056 0.0012
0.1875 Finishing Side 275 0.0047 0.15 0.0007
0.1875 Finishing Slot 200 0.0047 0.15 0.0004
0.1875 Finishing Contour 310 0.0047 0.0047 0.0008
0.25 Roughing Slot 165 0.25 0.025 0.0005
0.25 Roughing Side 230 0.025 0.25 0.0009
0.25 Roughing Contour 260 0.0075 0.0075 0.0012
0.25 Finishing Side 275 0.0063 0.2 0.0007
0.25 Finishing Slot 200 0.0063 0.2 0.0004
0.25 Finishing Contour 310 0.0063 0.0063 0.0008
0.3125 Roughing Slot 165 0.3125 0.0313 0.001
0.3125 Roughing Side 230 0.0313 0.3125 0.0019
0.3125 Roughing Contour 260 0.0094 0.0094 0.0024
0.3125 Finishing Side 275 0.0078 0.25 0.0013
0.3125 Finishing Slot 200 0.0078 0.25 0.0007
0.3125 Finishing Contour 310 0.0078 0.0078 0.0017
0.375 Roughing Slot 165 0.375 0.0375 0.001
0.375 Roughing Side 230 0.0375 0.375 0.0019
0.375 Roughing Contour 260 0.0113 0.0113 0.0024
0.375 Finishing Side 275 0.0094 0.3 0.0013
0.375 Finishing Slot 200 0.0094 0.3 0.0007
0.375 Finishing Contour 310 0.0094 0.0094 0.0017
0.5 Roughing Slot 165 0.5 0.05 0.0015
0.5 Roughing Side 230 0.05 0.5 0.0028
0.5 Roughing Contour 260 0.015 0.015 0.0035
0.5 Finishing Side 275 0.0125 0.4 0.002
0.5 Finishing Slot 200 0.0125 0.4 0.001
0.5 Finishing Contour 310 0.0125 0.0125 0.0025
0.625 Roughing Slot 165 0.625 0.0625 0.0015
0.625 Roughing Side 230 0.0625 0.625 0.0028
0.625 Roughing Contour 260 0.0188 0.0188 0.0035
0.625 Finishing Side 275 0.0156 0.5 0.002
0.625 Finishing Slot 200 0.0156 0.5 0.001
0.625 Finishing Contour 310 0.0156 0.0156 0.0025
0.75 Roughing Slot 165 0.75 0.075 0.0025
0.75 Roughing Side 230 0.075 0.75 0.0046
0.75 Roughing Contour 260 0.0225 0.0225 0.0059
0.75 Finishing Side 275 0.0188 0.6 0.0033
0.75 Finishing Slot 200 0.0188 0.6 0.0018
0.75 Finishing Contour 310 0.0188 0.0188 0.0041

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 70 0.3 3 0.012
3 Roughing Slot 50 3 0.3 0.006
3 Roughing Contour 80 0.09 0.09 0.015
4 Roughing Side 70 0.4 4 0.024
4 Roughing Slot 50 4 0.4 0.013
4 Roughing Contour 80 0.12 0.12 0.03
5 Roughing Side 70 0.5 5 0.024
5 Roughing Slot 50 5 0.5 0.013
5 Roughing Contour 80 0.15 0.15 0.03
6 Roughing Side 70 0.6 6 0.024
6 Roughing Slot 50 6 0.6 0.013
6 Roughing Contour 80 0.18 0.18 0.03
8 Roughing Side 70 0.8 8 0.047
8 Roughing Slot 50 8 0.8 0.026
8 Roughing Contour 80 0.24 0.24 0.06
10 Roughing Side 70 1 10 0.047
10 Roughing Slot 50 10 1 0.026
10 Roughing Contour 80 0.3 0.3 0.06
12 Roughing Side 70 1.2 12 0.071
12 Roughing Slot 50 12 1.2 0.038
12 Roughing Contour 80 0.36 0.36 0.09
16 Roughing Side 70 1.6 16 0.071
16 Roughing Slot 50 16 1.6 0.038
16 Roughing Contour 80 0.48 0.48 0.09
20 Roughing Side 70 2 20 0.118
20 Roughing Slot 50 20 2 0.064
20 Roughing Contour 80 0.6 0.6 0.15
3 Finishing Side 85 0.075 2.4 0.008
3 Finishing Slot 60 0.075 2.4 0.004
3 Finishing Contour 95 0.075 0.075 0.011
4 Finishing Side 85 0.1 3.2 0.017
4 Finishing Slot 60 0.1 3.2 0.009
4 Finishing Contour 95 0.1 0.1 0.021
5 Finishing Side 85 0.125 4 0.017
5 Finishing Slot 60 0.125 4 0.009
5 Finishing Contour 95 0.125 0.125 0.021
6 Finishing Side 85 0.15 4.8 0.017
6 Finishing Slot 60 0.15 4.8 0.009
6 Finishing Contour 95 0.15 0.15 0.021
8 Finishing Side 85 0.2 6.4 0.033
8 Finishing Slot 60 0.2 6.4 0.018
8 Finishing Contour 95 0.2 0.2 0.042
10 Finishing Side 85 0.25 8 0.033
10 Finishing Slot 60 0.25 8 0.018
10 Finishing Contour 95 0.25 0.25 0.042
12 Finishing Side 85 0.3 9.6 0.05
12 Finishing Slot 60 0.3 9.6 0.027
12 Finishing Contour 95 0.3 0.3 0.063
16 Finishing Side 85 0.4 12.8 0.05
16 Finishing Slot 60 0.4 12.8 0.027
16 Finishing Contour 95 0.4 0.4 0.063
20 Finishing Side 85 0.5 16 0.083
20 Finishing Slot 60 0.5 16 0.045
20 Finishing Contour 95 0.5 0.5 0.105
Super Alloy

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 65 0.125 0.01 0.0002
0.125 Roughing Side 100 0.01 0.125 0.0005
0.125 Roughing Contour 130 0.0038 0.0038 0.0006
0.125 Finishing Side 120 0.0031 0.1 0.0003
0.125 Finishing Slot 80 0.0031 0.1 0.0002
0.125 Finishing Contour 155 0.0031 0.0031 0.0004
0.1563 Roughing Slot 65 0.1563 0.0125 0.0005
0.1563 Roughing Side 100 0.0125 0.1563 0.0009
0.1563 Roughing Contour 130 0.0047 0.0047 0.0012
0.1563 Finishing Side 120 0.0039 0.125 0.0007
0.1563 Finishing Slot 80 0.0039 0.125 0.0003
0.1563 Finishing Contour 155 0.0039 0.0039 0.0008
0.1875 Roughing Slot 65 0.1875 0.015 0.0005
0.1875 Roughing Side 100 0.015 0.1875 0.0009
0.1875 Roughing Contour 130 0.0056 0.0056 0.0012
0.1875 Finishing Side 120 0.0047 0.15 0.0007
0.1875 Finishing Slot 80 0.0047 0.15 0.0003
0.1875 Finishing Contour 155 0.0047 0.0047 0.0008
0.25 Roughing Slot 65 0.25 0.02 0.0005
0.25 Roughing Side 100 0.02 0.25 0.0009
0.25 Roughing Contour 130 0.0075 0.0075 0.0012
0.25 Finishing Side 120 0.0063 0.2 0.0007
0.25 Finishing Slot 80 0.0063 0.2 0.0003
0.25 Finishing Contour 155 0.0063 0.0063 0.0008
0.3125 Roughing Slot 65 0.3125 0.025 0.001
0.3125 Roughing Side 100 0.025 0.3125 0.0019
0.3125 Roughing Contour 130 0.0094 0.0094 0.0024
0.3125 Finishing Side 120 0.0078 0.25 0.0013
0.3125 Finishing Slot 80 0.0078 0.25 0.0007
0.3125 Finishing Contour 155 0.0078 0.0078 0.0017
0.375 Roughing Slot 65 0.375 0.03 0.001
0.375 Roughing Side 100 0.03 0.375 0.0019
0.375 Roughing Contour 130 0.0113 0.0113 0.0024
0.375 Finishing Side 120 0.0094 0.3 0.0013
0.375 Finishing Slot 80 0.0094 0.3 0.0007
0.375 Finishing Contour 155 0.0094 0.0094 0.0017
0.5 Roughing Slot 65 0.5 0.04 0.0015
0.5 Roughing Side 100 0.04 0.5 0.0028
0.5 Roughing Contour 130 0.015 0.015 0.0035
0.5 Finishing Side 120 0.0125 0.4 0.002
0.5 Finishing Slot 80 0.0125 0.4 0.001
0.5 Finishing Contour 155 0.0125 0.0125 0.0025
0.625 Roughing Slot 65 0.625 0.05 0.0015
0.625 Roughing Side 100 0.05 0.625 0.0028
0.625 Roughing Contour 130 0.0188 0.0188 0.0035
0.625 Finishing Side 120 0.0156 0.5 0.002
0.625 Finishing Slot 80 0.0156 0.5 0.001
0.625 Finishing Contour 155 0.0156 0.0156 0.0025
0.75 Roughing Slot 65 0.75 0.06 0.0024
0.75 Roughing Side 100 0.06 0.75 0.0047
0.75 Roughing Contour 130 0.0225 0.0225 0.0059
0.75 Finishing Side 120 0.0188 0.6 0.0033
0.75 Finishing Slot 80 0.0188 0.6 0.0017
0.75 Finishing Contour 155 0.0188 0.0188 0.0041

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 30 0.24 3 0.012
3 Roughing Slot 20 3 0.24 0.006
3 Roughing Contour 40 0.09 0.09 0.015
4 Roughing Side 30 0.32 4 0.024
4 Roughing Slot 20 4 0.32 0.012
4 Roughing Contour 40 0.12 0.12 0.03
5 Roughing Side 30 0.4 5 0.024
5 Roughing Slot 20 5 0.4 0.012
5 Roughing Contour 40 0.15 0.15 0.03
6 Roughing Side 30 0.48 6 0.024
6 Roughing Slot 20 6 0.48 0.012
6 Roughing Contour 40 0.18 0.18 0.03
8 Roughing Side 30 0.64 8 0.048
8 Roughing Slot 20 8 0.64 0.025
8 Roughing Contour 40 0.24 0.24 0.06
10 Roughing Side 30 0.8 10 0.048
10 Roughing Slot 20 10 0.8 0.025
10 Roughing Contour 40 0.3 0.3 0.06
12 Roughing Side 30 0.96 12 0.072
12 Roughing Slot 20 12 0.96 0.037
12 Roughing Contour 40 0.36 0.36 0.09
16 Roughing Side 30 1.28 16 0.072
16 Roughing Slot 20 16 1.28 0.037
16 Roughing Contour 40 0.48 0.48 0.09
20 Roughing Side 30 1.6 20 0.12
20 Roughing Slot 20 20 1.6 0.062
20 Roughing Contour 40 0.6 0.6 0.15
3 Finishing Side 35 0.075 2.4 0.008
3 Finishing Slot 25 0.075 2.4 0.004
3 Finishing Contour 50 0.075 0.075 0.011
4 Finishing Side 35 0.1 3.2 0.017
4 Finishing Slot 25 0.1 3.2 0.008
4 Finishing Contour 50 0.1 0.1 0.021
5 Finishing Side 35 0.125 4 0.017
5 Finishing Slot 25 0.125 4 0.008
5 Finishing Contour 50 0.125 0.125 0.021
6 Finishing Side 35 0.15 4.8 0.017
6 Finishing Slot 25 0.15 4.8 0.008
6 Finishing Contour 50 0.15 0.15 0.021
8 Finishing Side 35 0.2 6.4 0.034
8 Finishing Slot 25 0.2 6.4 0.018
8 Finishing Contour 50 0.2 0.2 0.042
10 Finishing Side 35 0.25 8 0.034
10 Finishing Slot 25 0.25 8 0.018
10 Finishing Contour 50 0.25 0.25 0.042
12 Finishing Side 35 0.3 9.6 0.05
12 Finishing Slot 25 0.3 9.6 0.026
12 Finishing Contour 50 0.3 0.3 0.063
16 Finishing Side 35 0.4 12.8 0.05
16 Finishing Slot 25 0.4 12.8 0.026
16 Finishing Contour 50 0.4 0.4 0.063
20 Finishing Side 35 0.5 16 0.084
20 Finishing Slot 25 0.5 16 0.043
20 Finishing Contour 50 0.5 0.5 0.105
Titanium

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 195 0.125 0.0125 0.0002
0.125 Roughing Side 260 0.0125 0.125 0.0004
0.125 Roughing Contour 295 0.0038 0.0038 0.0006
0.125 Finishing Side 310 0.0031 0.1 0.0003
0.125 Finishing Slot 240 0.0031 0.1 0.0002
0.125 Finishing Contour 350 0.0031 0.0031 0.0004
0.1563 Roughing Slot 195 0.1563 0.0156 0.0005
0.1563 Roughing Side 260 0.0156 0.1563 0.0009
0.1563 Roughing Contour 295 0.0047 0.0047 0.0011
0.1563 Finishing Side 310 0.0039 0.125 0.0006
0.1563 Finishing Slot 240 0.0039 0.125 0.0004
0.1563 Finishing Contour 350 0.0039 0.0039 0.0008
0.1875 Roughing Slot 195 0.1875 0.0188 0.0005
0.1875 Roughing Side 260 0.0188 0.1875 0.0009
0.1875 Roughing Contour 295 0.0056 0.0056 0.0011
0.1875 Finishing Side 310 0.0047 0.15 0.0006
0.1875 Finishing Slot 240 0.0047 0.15 0.0004
0.1875 Finishing Contour 350 0.0047 0.0047 0.0008
0.25 Roughing Slot 195 0.25 0.025 0.0005
0.25 Roughing Side 260 0.025 0.25 0.0009
0.25 Roughing Contour 295 0.0075 0.0075 0.0011
0.25 Finishing Side 310 0.0063 0.2 0.0006
0.25 Finishing Slot 240 0.0063 0.2 0.0004
0.25 Finishing Contour 350 0.0063 0.0063 0.0008
0.3125 Roughing Slot 195 0.3125 0.0313 0.001
0.3125 Roughing Side 260 0.0313 0.3125 0.0018
0.3125 Roughing Contour 295 0.0094 0.0094 0.0022
0.3125 Finishing Side 310 0.0078 0.25 0.0013
0.3125 Finishing Slot 240 0.0078 0.25 0.0007
0.3125 Finishing Contour 350 0.0078 0.0078 0.0016
0.375 Roughing Slot 195 0.375 0.0375 0.001
0.375 Roughing Side 260 0.0375 0.375 0.0018
0.375 Roughing Contour 295 0.0113 0.0113 0.0022
0.375 Finishing Side 310 0.0094 0.3 0.0013
0.375 Finishing Slot 240 0.0094 0.3 0.0007
0.375 Finishing Contour 350 0.0094 0.0094 0.0016
0.5 Roughing Slot 195 0.5 0.05 0.0015
0.5 Roughing Side 260 0.05 0.5 0.0027
0.5 Roughing Contour 295 0.015 0.015 0.0033
0.5 Finishing Side 310 0.0125 0.4 0.0019
0.5 Finishing Slot 240 0.0125 0.4 0.001
0.5 Finishing Contour 350 0.0125 0.0125 0.0023
0.625 Roughing Slot 195 0.625 0.0625 0.0015
0.625 Roughing Side 260 0.0625 0.625 0.0027
0.625 Roughing Contour 295 0.0188 0.0188 0.0033
0.625 Finishing Side 310 0.0156 0.5 0.0019
0.625 Finishing Slot 240 0.0156 0.5 0.001
0.625 Finishing Contour 350 0.0156 0.0156 0.0023
0.75 Roughing Slot 195 0.75 0.075 0.0025
0.75 Roughing Side 260 0.075 0.75 0.0045
0.75 Roughing Contour 295 0.0225 0.0225 0.0056
0.75 Finishing Side 310 0.0188 0.6 0.0031
0.75 Finishing Slot 240 0.0188 0.6 0.0018
0.75 Finishing Contour 350 0.0188 0.0188 0.0039

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 80 0.3 3 0.011
3 Roughing Slot 60 3 0.3 0.006
3 Roughing Contour 90 0.09 0.09 0.014
4 Roughing Side 80 0.4 4 0.023
4 Roughing Slot 60 4 0.4 0.013
4 Roughing Contour 90 0.12 0.12 0.028
5 Roughing Side 80 0.5 5 0.023
5 Roughing Slot 60 5 0.5 0.013
5 Roughing Contour 90 0.15 0.15 0.028
6 Roughing Side 80 0.6 6 0.023
6 Roughing Slot 60 6 0.6 0.013
6 Roughing Contour 90 0.18 0.18 0.028
8 Roughing Side 80 0.8 8 0.046
8 Roughing Slot 60 8 0.8 0.026
8 Roughing Contour 90 0.24 0.24 0.057
10 Roughing Side 80 1 10 0.046
10 Roughing Slot 60 10 1 0.026
10 Roughing Contour 90 0.3 0.3 0.057
12 Roughing Side 80 1.2 12 0.068
12 Roughing Slot 60 12 1.2 0.038
12 Roughing Contour 90 0.36 0.36 0.085
16 Roughing Side 80 1.6 16 0.068
16 Roughing Slot 60 16 1.6 0.038
16 Roughing Contour 90 0.48 0.48 0.085
20 Roughing Side 80 2 20 0.114
20 Roughing Slot 60 20 2 0.064
20 Roughing Contour 90 0.6 0.6 0.142
3 Finishing Side 95 0.075 2.4 0.008
3 Finishing Slot 70 0.075 2.4 0.004
3 Finishing Contour 110 0.075 0.075 0.01
4 Finishing Side 95 0.1 3.2 0.016
4 Finishing Slot 70 0.1 3.2 0.009
4 Finishing Contour 110 0.1 0.1 0.02
5 Finishing Side 95 0.125 4 0.016
5 Finishing Slot 70 0.125 4 0.009
5 Finishing Contour 110 0.125 0.125 0.02
6 Finishing Side 95 0.15 4.8 0.016
6 Finishing Slot 70 0.15 4.8 0.009
6 Finishing Contour 110 0.15 0.15 0.02
8 Finishing Side 95 0.2 6.4 0.032
8 Finishing Slot 70 0.2 6.4 0.018
8 Finishing Contour 110 0.2 0.2 0.04
10 Finishing Side 95 0.25 8 0.032
10 Finishing Slot 70 0.25 8 0.018
10 Finishing Contour 110 0.25 0.25 0.04
12 Finishing Side 95 0.3 9.6 0.048
12 Finishing Slot 70 0.3 9.6 0.027
12 Finishing Contour 110 0.3 0.3 0.06
16 Finishing Side 95 0.4 12.8 0.048
16 Finishing Slot 70 0.4 12.8 0.027
16 Finishing Contour 110 0.4 0.4 0.06
20 Finishing Side 95 0.5 16 0.08
20 Finishing Slot 70 0.5 16 0.045
20 Finishing Contour 110 0.5 0.5 0.099
Tool Steel (>48≤56HRC)

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 130 0.125 0.0063 0.0002
0.125 Roughing Side 200 0.0063 0.125 0.0004
0.125 Roughing Contour 230 0.0038 0.0038 0.0006
0.125 Finishing Side 240 0.0031 0.1 0.0003
0.125 Finishing Slot 155 0.0031 0.1 0.0002
0.125 Finishing Contour 275 0.0031 0.0031 0.0004
0.1563 Roughing Slot 130 0.1563 0.0078 0.0003
0.1563 Roughing Side 200 0.0078 0.1563 0.0008
0.1563 Roughing Contour 230 0.0047 0.0047 0.0011
0.1563 Finishing Side 240 0.0039 0.125 0.0006
0.1563 Finishing Slot 155 0.0039 0.125 0.0002
0.1563 Finishing Contour 275 0.0039 0.0039 0.0008
0.1875 Roughing Slot 130 0.1875 0.0094 0.0003
0.1875 Roughing Side 200 0.0094 0.1875 0.0008
0.1875 Roughing Contour 230 0.0056 0.0056 0.0011
0.1875 Finishing Side 240 0.0047 0.15 0.0006
0.1875 Finishing Slot 155 0.0047 0.15 0.0002
0.1875 Finishing Contour 275 0.0047 0.0047 0.0008
0.25 Roughing Slot 130 0.25 0.0125 0.0003
0.25 Roughing Side 200 0.0125 0.25 0.0008
0.25 Roughing Contour 230 0.0075 0.0075 0.0011
0.25 Finishing Side 240 0.0063 0.2 0.0006
0.25 Finishing Slot 155 0.0063 0.2 0.0002
0.25 Finishing Contour 275 0.0063 0.0063 0.0008
0.3125 Roughing Slot 130 0.3125 0.0156 0.0006
0.3125 Roughing Side 200 0.0156 0.3125 0.0016
0.3125 Roughing Contour 230 0.0094 0.0094 0.0022
0.3125 Finishing Side 240 0.0078 0.25 0.0011
0.3125 Finishing Slot 155 0.0078 0.25 0.0004
0.3125 Finishing Contour 275 0.0078 0.0078 0.0015
0.375 Roughing Slot 130 0.375 0.0188 0.0006
0.375 Roughing Side 200 0.0188 0.375 0.0016
0.375 Roughing Contour 230 0.0113 0.0113 0.0022
0.375 Finishing Side 240 0.0094 0.3 0.0011
0.375 Finishing Slot 155 0.0094 0.3 0.0004
0.375 Finishing Contour 275 0.0094 0.0094 0.0015
0.5 Roughing Slot 130 0.5 0.025 0.0009
0.5 Roughing Side 200 0.025 0.5 0.0024
0.5 Roughing Contour 230 0.015 0.015 0.0033
0.5 Finishing Side 240 0.0125 0.4 0.0017
0.5 Finishing Slot 155 0.0125 0.4 0.0007
0.5 Finishing Contour 275 0.0125 0.0125 0.0023
0.625 Roughing Slot 130 0.625 0.0313 0.0009
0.625 Roughing Side 200 0.0313 0.625 0.0024
0.625 Roughing Contour 230 0.0188 0.0188 0.0033
0.625 Finishing Side 240 0.0156 0.5 0.0017
0.625 Finishing Slot 155 0.0156 0.5 0.0007
0.625 Finishing Contour 275 0.0156 0.0156 0.0023
0.75 Roughing Slot 130 0.75 0.0375 0.0016
0.75 Roughing Side 200 0.0375 0.75 0.0039
0.75 Roughing Contour 230 0.0225 0.0225 0.0055
0.75 Finishing Side 240 0.0188 0.6 0.0028
0.75 Finishing Slot 155 0.0188 0.6 0.0011
0.75 Finishing Contour 275 0.0188 0.0188 0.0039

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 60 0.15 3 0.01
3 Roughing Slot 40 3 0.15 0.006
3 Roughing Contour 70 0.09 0.09 0.014
4 Roughing Side 60 0.2 4 0.02
4 Roughing Slot 40 4 0.2 0.008
4 Roughing Contour 70 0.12 0.12 0.028
5 Roughing Side 60 0.25 5 0.02
5 Roughing Slot 40 5 0.25 0.008
5 Roughing Contour 70 0.15 0.15 0.028
6 Roughing Side 60 0.3 6 0.02
6 Roughing Slot 40 6 0.3 0.008
6 Roughing Contour 70 0.18 0.18 0.028
8 Roughing Side 60 0.4 8 0.04
8 Roughing Slot 40 8 0.4 0.016
8 Roughing Contour 70 0.24 0.24 0.056
10 Roughing Side 60 0.5 10 0.04
10 Roughing Slot 40 10 0.5 0.016
10 Roughing Contour 70 0.3 0.3 0.056
12 Roughing Side 60 0.6 12 0.06
12 Roughing Slot 40 12 0.6 0.024
12 Roughing Contour 70 0.36 0.36 0.084
16 Roughing Side 60 0.8 16 0.06
16 Roughing Slot 40 16 0.8 0.024
16 Roughing Contour 70 0.48 0.48 0.084
20 Roughing Side 60 1 20 0.1
20 Roughing Slot 40 20 1 0.04
20 Roughing Contour 70 0.6 0.6 0.14
3 Finishing Side 70 0.075 2.4 0.007
3 Finishing Slot 50 0.075 2.4 0.004
3 Finishing Contour 85 0.075 0.075 0.01
4 Finishing Side 70 0.1 3.2 0.014
4 Finishing Slot 50 0.1 3.2 0.006
4 Finishing Contour 85 0.1 0.1 0.02
5 Finishing Side 70 0.125 4 0.014
5 Finishing Slot 50 0.125 4 0.006
5 Finishing Contour 85 0.125 0.125 0.02
6 Finishing Side 70 0.15 4.8 0.014
6 Finishing Slot 50 0.15 4.8 0.006
6 Finishing Contour 85 0.15 0.15 0.02
8 Finishing Side 70 0.2 6.4 0.028
8 Finishing Slot 50 0.2 6.4 0.011
8 Finishing Contour 85 0.2 0.2 0.039
10 Finishing Side 70 0.25 8 0.028
10 Finishing Slot 50 0.25 8 0.011
10 Finishing Contour 85 0.25 0.25 0.039
12 Finishing Side 70 0.3 9.6 0.042
12 Finishing Slot 50 0.3 9.6 0.017
12 Finishing Contour 85 0.3 0.3 0.059
16 Finishing Side 70 0.4 12.8 0.042
16 Finishing Slot 50 0.4 12.8 0.017
16 Finishing Contour 85 0.4 0.4 0.059
20 Finishing Side 70 0.5 16 0.07
20 Finishing Slot 50 0.5 16 0.028
20 Finishing Contour 85 0.5 0.5 0.098
Tool Steel (≤48HRC)

Inch

Diameter (in) Operation Cut Vc (SFM) Ae (in) Ap (in) Fz (in/tooth)
0.125 Roughing Slot 295 0.125 0.0125 0.0003
0.125 Roughing Side 360 0.0125 0.125 0.0005
0.125 Roughing Contour 395 0.0038 0.0038 0.0006
0.125 Finishing Side 430 0.0031 0.1 0.0004
0.125 Finishing Slot 350 0.0031 0.1 0.0002
0.125 Finishing Contour 475 0.0031 0.0031 0.0004
0.1563 Roughing Slot 295 0.1563 0.0156 0.0005
0.1563 Roughing Side 360 0.0156 0.1563 0.001
0.1563 Roughing Contour 395 0.0047 0.0047 0.0013
0.1563 Finishing Side 430 0.0039 0.125 0.0007
0.1563 Finishing Slot 350 0.0039 0.125 0.0003
0.1563 Finishing Contour 475 0.0039 0.0039 0.0009
0.1875 Roughing Slot 295 0.1875 0.0188 0.0005
0.1875 Roughing Side 360 0.0188 0.1875 0.001
0.1875 Roughing Contour 395 0.0056 0.0056 0.0013
0.1875 Finishing Side 430 0.0047 0.15 0.0007
0.1875 Finishing Slot 350 0.0047 0.15 0.0003
0.1875 Finishing Contour 475 0.0047 0.0047 0.0009
0.25 Roughing Slot 295 0.25 0.025 0.0005
0.25 Roughing Side 360 0.025 0.25 0.001
0.25 Roughing Contour 395 0.0075 0.0075 0.0013
0.25 Finishing Side 430 0.0063 0.2 0.0007
0.25 Finishing Slot 350 0.0063 0.2 0.0003
0.25 Finishing Contour 475 0.0063 0.0063 0.0009
0.3125 Roughing Slot 295 0.3125 0.0313 0.0009
0.3125 Roughing Side 360 0.0313 0.3125 0.002
0.3125 Roughing Contour 395 0.0094 0.0094 0.0025
0.3125 Finishing Side 430 0.0078 0.25 0.0014
0.3125 Finishing Slot 350 0.0078 0.25 0.0007
0.3125 Finishing Contour 475 0.0078 0.0078 0.0018
0.375 Roughing Slot 295 0.375 0.0375 0.0009
0.375 Roughing Side 360 0.0375 0.375 0.002
0.375 Roughing Contour 395 0.0113 0.0113 0.0025
0.375 Finishing Side 430 0.0094 0.3 0.0014
0.375 Finishing Slot 350 0.0094 0.3 0.0007
0.375 Finishing Contour 475 0.0094 0.0094 0.0018
0.5 Roughing Slot 295 0.5 0.05 0.0014
0.5 Roughing Side 360 0.05 0.5 0.0031
0.5 Roughing Contour 395 0.015 0.015 0.0038
0.5 Finishing Side 430 0.0125 0.4 0.0021
0.5 Finishing Slot 350 0.0125 0.4 0.001
0.5 Finishing Contour 475 0.0125 0.0125 0.0026
0.625 Roughing Slot 295 0.625 0.0625 0.0014
0.625 Roughing Side 360 0.0625 0.625 0.0031
0.625 Roughing Contour 395 0.0188 0.0188 0.0038
0.625 Finishing Side 430 0.0156 0.5 0.0021
0.625 Finishing Slot 350 0.0156 0.5 0.001
0.625 Finishing Contour 475 0.0156 0.0156 0.0026
0.75 Roughing Slot 295 0.75 0.075 0.0024
0.75 Roughing Side 360 0.075 0.75 0.0051
0.75 Roughing Contour 395 0.0225 0.0225 0.0063
0.75 Finishing Side 430 0.0188 0.6 0.0036
0.75 Finishing Slot 350 0.0188 0.6 0.0017
0.75 Finishing Contour 475 0.0188 0.0188 0.0044

Metric

Diameter (mm) Operation Cut Vc (m/min) Ae (mm) Ap (mm) Fz (mm/tooth)
3 Roughing Side 110 0.3 3 0.013
3 Roughing Slot 90 3 0.3 0.007
3 Roughing Contour 120 0.09 0.09 0.016
4 Roughing Side 110 0.4 4 0.026
4 Roughing Slot 90 4 0.4 0.012
4 Roughing Contour 120 0.12 0.12 0.032
5 Roughing Side 110 0.5 5 0.026
5 Roughing Slot 90 5 0.5 0.012
5 Roughing Contour 120 0.15 0.15 0.032
6 Roughing Side 110 0.6 6 0.026
6 Roughing Slot 90 6 0.6 0.012
6 Roughing Contour 120 0.18 0.18 0.032
8 Roughing Side 110 0.8 8 0.052
8 Roughing Slot 90 8 0.8 0.024
8 Roughing Contour 120 0.24 0.24 0.064
10 Roughing Side 110 1 10 0.052
10 Roughing Slot 90 10 1 0.024
10 Roughing Contour 120 0.3 0.3 0.064
12 Roughing Side 110 1.2 12 0.078
12 Roughing Slot 90 12 1.2 0.036
12 Roughing Contour 120 0.36 0.36 0.096
16 Roughing Side 110 1.6 16 0.078
16 Roughing Slot 90 16 1.6 0.036
16 Roughing Contour 120 0.48 0.48 0.096
20 Roughing Side 110 2 20 0.13
20 Roughing Slot 90 20 2 0.06
20 Roughing Contour 120 0.6 0.6 0.16
3 Finishing Side 130 0.075 2.4 0.009
3 Finishing Slot 110 0.075 2.4 0.005
3 Finishing Contour 145 0.075 0.075 0.011
4 Finishing Side 130 0.1 3.2 0.018
4 Finishing Slot 110 0.1 3.2 0.008
4 Finishing Contour 145 0.1 0.1 0.022
5 Finishing Side 130 0.125 4 0.018
5 Finishing Slot 110 0.125 4 0.008
5 Finishing Contour 145 0.125 0.125 0.022
6 Finishing Side 130 0.15 4.8 0.018
6 Finishing Slot 110 0.15 4.8 0.008
6 Finishing Contour 145 0.15 0.15 0.022
8 Finishing Side 130 0.2 6.4 0.036
8 Finishing Slot 110 0.2 6.4 0.017
8 Finishing Contour 145 0.2 0.2 0.045
10 Finishing Side 130 0.25 8 0.036
10 Finishing Slot 110 0.25 8 0.017
10 Finishing Contour 145 0.25 0.25 0.045
12 Finishing Side 130 0.3 9.6 0.055
12 Finishing Slot 110 0.3 9.6 0.025
12 Finishing Contour 145 0.3 0.3 0.067
16 Finishing Side 130 0.4 12.8 0.055
16 Finishing Slot 110 0.4 12.8 0.025
16 Finishing Contour 145 0.4 0.4 0.067
20 Finishing Side 130 0.5 16 0.091
20 Finishing Slot 110 0.5 16 0.042
20 Finishing Contour 145 0.5 0.5 0.112

!